ELTRON TLP 2046 DRIVER DOWNLOAD

Don’t show me this message again. Page 24 Operation Label Loading Open the Printhead Assembly by pushing the release lever to the right, towards the back of Step the printer. Operation Transfer Ribbon Open the printhead assembly. Do Not dispose of the old battery in fire. Figure Attaching Ribbon Tape Page 29 Operation Label Loading Close the printhead by pressing down on both Step 7 sides of the front of the printhead assembly. Push the roll to the back of the support and slide the Label Roll Guide against the label roll to hold it in place.

Uploader: Mami
Date Added: 20 April 2011
File Size: 21.10 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 39925
Price: Free* [*Free Regsitration Required]

Press the Enter key. Technical Support, Copyright Notice Eltron International Incorporated and may eltroon be duplicated in full or in part by any person without written approval from Eltron.

Operation Label Loading Close the printhead by pressing down on both Step 7 sides of eltron tlp 2046 front of the printhead eltron tlp 2046. Ensure that Print Configuration Control switch setting match the print mode.

Page of 68 Go. Page 47 Operation Windows: Don’t have an account? Page 17 Getting Started Step 4 The printer has a manual configuration switch bank located on the back panel of the printer. Page 16 Getting Started Step Parallel Interface Attach a suitable parallel printer cable from eltron tlp 2046 Attach Interface computer to the Centronics interface connector Cable at the back of the printer. This manual also for: Operation Label Loading Open the Eltron tlp 2046 Assembly by pushing the release lever to the right, towards the back of Step the printer.

Try Also -   Lg p698 user manual download

Listed below are barcode printers and barcode printer family drivers eltron tlp 2046 by Loftware. Figure Electrical Outlet Insert Page 62 Accessories Rev. Page 29 Operation Label Loading Close the printhead by pressing down on both Step 7 sides of the front of the printhead assembly. Setting When using Windows applications other than Create-A-Label Professional, the following the Margins margin setting guidelines should be followed: Trouble Shooting Problem Solution or Reason 1.

Labels feed from Step the top and towards the front of the printer.

Thermal Transfer cross reference list

Fold the label liner over the clip to the back of the printer. Slide the Replacement Step eltron tlp 2046 casing fltron cover off. Place this switch in the OFF 0 position to remove power when you have finished using your printer. Page 48 Operation Rev. Page 30 Operation Label Loading Adjust the label pressure control knob to match Step 8 the label stock in use.

This is referred to as eltron tlp 2046 Form Feed.

Page 9 Getting Started Open the top and eltron tlp 2046 side cover by lifting the lip on the lower right side of the cover. Figure Adjusting the Eltron tlp 2046 Arm Operation AutoSense Load labels into the printer.

The battery may explode causing damage or injury. Warranty Information, Fcc Notice 12 months from the date of purchase by the end user.

Supported Labeling Printers

Operation Label Loading Adjust the label pressure control knob to match Step 8 the label eltron tlp 2046 in use. Push the cartridge slowly and eltfon, until it stops, to engage.

Try Also -   Rar password cracker 4.12 keygen

Possible problem with label stock.

Step Place the printer in a suitable location that Attach Power allows easy elrton to all sides of the printer. Check the location of the Through Sen- sor, refer to Appendix A for adjustment infor- mation.

Alternate memory cartridges are available that can include a real-time clock standard configu- ration without real-time clockEltron tlp 2046 of mem- ory and 2 Dimensional bar codes.

Eltron tlp 2046 66 Windows Printer Driver Rev. Introduction This section provides information on the instal- lation of the TLP printer and software. Save this screw for mounting and storing the bracket. Operation Loading Labels Your TLP can print on continuous direct thermal paper, direct thermal adhesive backed or Tags eltron tlp 2046 or non-adhesive tags.

Page 32 Operation Transfer Ribbon Open the printhead assembly.

Eltron tlp 2046 this switch in the ON 1 position will apply power to the printer. Table Of Contents Introduction By pressing ‘print’ button you will print only current page.

Show Buttons
Hide Buttons